1 or 2 Channel Switch (ASW1/2)

PRODUCTS


1 or 2 Channel Switch (ASW1/2)

Mx-ASW1 / Mx-ASW2

Description

The light switch is a battery free wireless transmitter that communicates with a wide variety of receivers. Every time the light switch is pressed, a small micro generator produces a small electrical current that powers a built in transmitter. This transmitter sends wireless signals that command the relay/receiver to turn a device ON or OFF. With an appropriate receiver, the switch can even be used to control the dimming of lights. CE-Conformity: 89/336/EWG Electromagnetic compatibility R&TTE 1999/5/EC Radio and Telecommunications Terminal Equipment Directive Standards: ETSI EN 301 489-1: 2001-09 ETSI EN 301 489-3: 2001-11 ETSI EN 61000-6-2: 2002-08 ETSI EN 300 220-3: 2000-09 The general registration for the radio operation is valid for all EU-countries as well as for Switzerland. FCC ID: SZV-PTM200 This device complies with Part 15 of the FCC Rules and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications made to this equipment not expressly approved by Magnum may void the FCC authorization to operate this equipment.

 

Norms & Standards

CE-Conformity:

89/336/EWG Electromagnetic compatibility R&TTE 1999/5/EC Radio and Telecommunications Terminal Equipment Directive

Standards:

ETSI EN 301 489-1: 2001-09 ETSI EN 301 489-3: 2001-11 ETSI EN 61000-6-2: 2002-08 ETSI EN 300 220-3: 2000-09 The general registration for the radio operation is valid for all EU-countries as well as for Switzerland.

FCC ID: SZV-PTM200
This device complies with Part 15 of the FCC Rules and RSS210 of Industry Canada.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications made to this equipment not expressly approved by Magnum may void the FCC authorization to operate this equipment.

Lighting Control

ALL LIGHTING CONTROL PRODUCTS

Smart Repeater
Smart Repeater
Mx-USR-RPT

Wireless Repeater which receives telegrams and re-sends them to enhance and increase the signal distance from the transmitter to the receiver. Typically a repeater will be used when the sensor has been mounted too far from the receiver or there are obstacles between the sensor and receiver which diminishes the signal.
cut sheet »
installation guide »
Automatic Load Control Relay
Automatic Load Control Relay
Mx-ALCR

The Magnum MX-ALCR is a UL 924 listed emergency lighting control device. This device is designed to ensure a “lights on state” during a power outage. The MX-ALCR senses when a power outage occurs and switches on the connected emergency lighting load to full brightness, bypassing any normal lighting switches and dimmer controls.
cut sheet »
Wireless Motion / Lux Sensor
Wireless Motion / Lux Sensor
Mx-ML2

The Mx-ML2 is a wireless, self powered, passive infrared sensor that ensures reliable detection of occupant presence, and is ideally suited for occupancy-based lighting control.
cut sheet »
installation guide »
Wireless Occupancy Sensor
Wireless Occupancy Sensor
Mx-EOSC (ceiling mounted)

The ceiling-mounted occupancy sensor saves energy and adds convenience by accurately detecting when an area is occupied or vacant.
cut sheet »
installation guide »
Wireless Occupancy Sensor
Wireless Occupancy Sensor
Mx-EOSW (wall mounted)

The wall-mounted occupancy sensor saves energy and adds convenience by accurately detecting when an area is occupied or vacant.
cut sheet »
installation guide »
0-10V Lighting Control Module (metering & temp)(LM)
0-10V Lighting Control Module (metering & temp)(LM)
Mx-USR-LM

The Mx-USR-LM offers bi-directional, ON/OFF and 0-10V dimming control when combined with a wireless light switch or automatic shut-off when combined with a wireless occupancy sensor.
cut sheet »
installation guide »
1 or 2 Channel Switch (ZigBee EDRP / ESRP)
1 or 2 Channel Switch (ZigBee EDRP / ESRP)
MZ-ESRP / MZ-EDRP

Wireless (via ZigBee transmitter module) and battery-free, one or two channel light switch. A clean contemporary design makes them an attractive addition to any decor.
cut sheet »
installation guide »
1 or 2 Channel Switch (ZigBee ASW1/2)
1 or 2 Channel Switch (ZigBee ASW1/2)
MZ-ASW1 / MZ-ASW2

The light switch is a battery-free wireless transmitter (via ZigBee transmitter module) that communicates with a wide variety of receivers. Multiple color / finish options available.

1 or 2 Channel Switch (ASW1/2)
1 or 2 Channel Switch (ASW1/2)
Mx-ASW1 / Mx-ASW2

The light switch is a battery-free wireless transmitter that communicates with a wide variety of receivers. Multiple color / finish options available.
cut sheet »
installation guide »
1 or 2 Channel Switch (ESRP/EDRP)
1 or 2 Channel Switch (ESRP/EDRP)
Mx-EDRP / Mx-ESRP

Wireless and battery-free one or two channel light switch. A clean contemporary design makes them an attractive addition to any decor.
cut sheet »
installation guide »
Integrated Light Switch
Integrated Light Switch
Mx-ILS2

This integrated light switch fits in a standard single gange wall box and can work in conjunction with Magnum wireless control products.
cut sheet »
installation guide »
Lighting Node (LBKO10V)
Lighting Node (LBKO10V)
Mx-OPUS-LBKO10V (low bay)

When the device is connected to 0-10V dim-to-off drivers, it enables any lighting manufacturer to deliver simple, fully connected fixtures.
cut sheet »
Lighting Node (LBKOD)
Lighting Node (LBKOD)
Mx-OPUS-LBKOD (low bay)

In fixture DALI lighting controller with digital PIR and ambient light sensing for daylight harvesting applications as well as occupancy detection.
cut sheet »
In-Fixture Lighting Node (10V12)
In-Fixture Lighting Node (10V12)
Mx-OPUS-10V12

The Mx-OPUS-10V12 is compatible with 0-10V, dim-to-off LED drivers. The device is powered through available low voltage from the driver or an available 12-15VDC source.
cut sheet »
2-Channel In-Fixture Lighting Node (10V12-2)
2-Channel In-Fixture Lighting Node (10V12-2)
Mx-OPUS-10V12-2

The Mx-OPUS-10V12-2 (2 channels) is compatible with 0-10V, dim-to-off LED drivers. The device is powered through available low voltage from the driver or an available 12-15VDC source.
cut sheet »
In-Fixture Lighting Node (DR10V)
In-Fixture Lighting Node (DR10V)
Mx-OPUS-DR10V

Compatible with 0-10V, dim-to-off LED drivers. The device is powered through available low voltage from the driver or an available 12-36 VDC, 12-24 VAC source near the fixture level.
cut sheet »
In-Fixture Lighting Node (DRD)
In-Fixture Lighting Node (DRD)
Mx-OPUS-DRD

The Mx-OPUS-DRD provides for bi-directional, fixture level wireless DALI (digital addressable lighting interface) lighting control integration.
cut sheet »
In-Fixture Lighting Node (DRDHV)
In-Fixture Lighting Node (DRDHV)
Mx-OPUS-DRDHV

The Mx-OPUS-DRDHV provides for bi-directional, fixture level wireless DALI (digital addressable lighting interface) lighting control integration.
cut sheet »
In-Fixture Lighting Node (DRDLV)
In-Fixture Lighting Node (DRDLV)
Mx-OPUS-DRDLV

The Mx-OPUS-DRDLV provides for bi-directional, fixture level wireless DALI (digital addressable lighting interface) lighting control integration.
cut sheet »
Lighting Node (HBKO10V)
Lighting Node (HBKO10V)
Mx-OPUS-HBKO10V

When the device is connected to 0-10V dim-to-off drivers, it enables any lighting manufacturer to deliver simple, fully connected fixtures.
cut sheet »
Lighting Node (HBKOD)
Lighting Node (HBKOD)
Mx-OPUS-HBKOD

In fixture DALI lighting controller with digital PIR and ambient light sensing for daylight harvesting applications as well as occupancy detection.
cut sheet »
Wired Motion / Lux Sensor (HPML)
Wired Motion / Lux Sensor (HPML)
Mx-OPUS-HPML (high bay)

Wired motion / lux sensor that works in tandem with Magnum’s OPUS-DRD, DR10V, DRDHV and DRDLV to add additional control to your fixture.
cut sheet »
In-Fixture Lighting Node (ML10V)
In-Fixture Lighting Node (ML10V)
Mx-OPUS-ML10V (low bay)

Connecting the device to 0-10V dim-to-off drivers, enables any lighting manufacturer to deliver simple, fully connected fixtures. The small, sleek form factor includes a PIR / Lux sensor.
cut sheet »
In-Fixture Lighting Node (ML10VHB)
In-Fixture Lighting Node (ML10VHB)
Mx-OPUS-ML10VHB (high bay)

Connecting the device to 0-10V dim-to-off drivers, enables any lighting manufacturer to deliver simple, fully connected fixtures. The small, sleek form factor includes a PIR / Lux sensor.
cut sheet »
In-Fixture Lighting Node (MLD)
In-Fixture Lighting Node (MLD)
Mx-OPUS-MLD (low bay)

Connecting the device to a Philips Xitanium SR Driver or a DALI driver, enables any lighting manufacturer to deliver fully connected fixtures. The small form factor includes a PIR / Lux sensor.

In-Fixture Lighting Node (MLDHB)
In-Fixture Lighting Node (MLDHB)
Mx-OPUS-MLDHB

Connecting the device to a Philips Xitanium SR Driver or a DALI driver, enables any lighting manufacturer to deliver fully connected fixtures. The small form factor includes a PIR / Lux sensor.
cut sheet »
In-Fixture Lighting Node (MLDE)
In-Fixture Lighting Node (MLDE)
Mx-OPUS-MLDE (highbay)

Connecting the device to a Philips Xitanium SR Driver or a DALI driver, enables any lighting manufacturer to deliver fully connected fixtures. The small form factor includes a PIR / Lux sensor.
cut sheet »
PWM LED Dimming Module
PWM LED Dimming Module
Mx-OPUS-PWMLV

The Magnum Energy Solution’s PWM LED Dimming Control Module, through the use of thousands of PWM dimming steps, creates what is perceived by the natural eye as a single continuous dim, even at extremely low light levels.
cut sheet »
1 Channel Lighting Relay (USR-L3)
1 Channel Lighting Relay (USR-L3)
Mx-USR-L3

The Mx-USR-L3 offers bi-directional, ON/OFF and 0-10V dimming control when combined with a wireless light switch or automatic shut-off when combined with a wireless occ sensor.
cut sheet »
installation guide »
2 Channel Lighting Relay (UTR-L3)
2 Channel Lighting Relay (UTR-L3)
Mx-UTR-L3

The Mx-UTR-L3 offers bi-directional, ON/OFF and 0-10V dimming control when combined with a wireless light switch or automatic shut-off when combined with a wireless occ sensor.
cut sheet »
installation guide »
1 Channel Lighting Relay (PWM)
1 Channel Lighting Relay (PWM)
Mx-USR-L3PWM

The Mx-USR-L3PWM offers bi-directional, ON/OFF and 0-10V dimming control when combined with a wireless light switch or automatic shut-off when combined with a wireless occ sensor.
cut sheet »